Total: £0

toly (Price shown excludes VAT)

01708 525 866

Total: £0

toly (Price shown excludes VAT)

Laminate and Wood

Laminate and Wood
  • Bond-It 1 Part Wood Filler 250ml – Box of 6

    £11.61£12.60

    An easy to use, ready mixed, high quality, solvent‐free filler, ideal for filling small imperfections (max 5mm depth) and covering the recesses left by nails and screws in wood.

    BENEFITS

    – Can be stained, painted, varnished or dyed once cured.
    – Solvent‐free, low odour and non‐flammable.
    – Waterproof.
    – Suitable for internal and external applications.

    USES

    General wood filling of windowsills, frames, bannisters, MDF and laminates, etc. Repairing wood damaged by wet rot in both internal and external locations. Repair damage and chips to parquet or laminate flooring, wooden furniture, etc.

    PREPARATION

    Ensure the repair area is clean and dry and free from dust or any contamination that may affect adhesion. Wet down the surfaces that the material is to be applied to. NOTE: If you intend to overstain the repair, choose the filler colour closest to the wood you are filling, not the stain you intend to use. Always check the stain on a small area as the filler may absorb the stain at a different rate to the wood. As the filler may absorb some stains at different rates to the surrounding timber, always test a small area first.

    APPLICATION

    Stir well before use. Apply with a wetted filling knife or spreader, forcing into cracks and holes. For deep holes, build up in layers allowing each layer to dry. Leave slightly proud, and when completely dry, sand down. Drying time – touch dry in 30 minutes. When overpainting, staining or varnishing, you may get a colour difference with the surrounding wood, so always check on a small area first. Do not add stain to Bond It ALL PURPOSE WOOD FILLER. Not suitable for filling gaps between floorboards.

    LIMITATIONS

    As the filler may absorb some stains at different rates to the surrounding timber, always test a small area first. Note: filler may dry darker. Do not exceed 5mm in one coat. For holes deeper than 5mm or for areas subject to impact, such as doors and window frames, use Bond It 2 PART WOOD FILLER. Protect from rain when used externally for at least 5 hours. Do not apply below 5o C.

     

    For our full range of filler for wood, please click here. For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it, please visit their website here.

  • Bond-It 2 Part Wood Filler 275ml – Box of 6

    £40.77

    Bond-It 2 Part Wood Filler is a tough, durable, two part wood filler based on polyester resin. Long lasting repair for all wood types

    BENEFITS

    – Can be stained, painted, varnished or dyed once cured.
    – Chemical curing system ‐ sets hard in 30 minutes to any depth.
    – Sandable in 30 minutes.
    – High strength; can be drilled, nailed, planed and carved once dry.
    – Good movement capabilities to flex with wood. No shrinking or cracking. w Waterproof, suitable for internal and external application.

    USES

    2 Part Wood Filler is a general wood filling of windowsills, frames, banisters, MDF and laminates, etc. Repairing wood damaged by wet rot in both internal and external locations. Repair damage and chips to parquet or laminate flooring, wooden furniture, etc.

    PREPARATION

    Ensure the repair area is clean and dry and free from dust or any contamination that may affect adhesion. Any rotten wood should be totally removed. If you intend to overstain the repair, choose the filler colour closest to the wood you are filling, not the stain you intend to use. Always check the stain on a small area as the filler may absorb the stain at a different rate to the wood.

    APPLICATION

    Mix a golf ball volume of filler (approx. 38mm diameter and a 38mm strip of hardener into a homogeneous paste with the spatula provided. Press firmly into the surface to be repaired, leaving it slightly proud. Leave to dry for about 30 minutes until hard before finishing (sanding and or painting/staining).

    LIMITATIONS

    Do not attempt to push mixture back into pack once mixed. Avoid contact with eyes and skin. Always test a small inconspicuous area for colour matching purposes. Throw away any unused mixed material after 10 minutes.

     

    For our full range of filler for wood, please click here. For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it, please visit their website here.

  • Bond-It Duo 2 in 1 Wood Glue

    £17.64£394.08

    Uses DUO “2 IN 1” WOOD GLUE can be used as a general-purpose joinery adhesive or for applications where long term resistance to moisture is a pre-requisite of the adhesive. Suitable for hard and softwoods, decorative laminates, chipboard blockwood and other engineered timber panels. It is also suitable for use with RF bonding machinery. Not suitable for permanent immersion in water.

    PREPARATION

    Surfaces to be bonded must be clean, dry and free from dust, grease or contaminants that may hinder adhesion.

    APPLICATION

    Apply the adhesive to one surface only and bring the two surfaces together within 3-4 minutes and clamp for approximately 1 hour. After 1 hour, careful handling is permissible. Glued components should be left overnight before machining. Remove excess adhesive whilst wet using a damp cloth. When using RF bonding techniques, the user must explore the most efficient combination of glue application, power and dwell time as each of these varies with different machinery and constructions.

    LIMITATIONS

    Do not use on surfaces below 5oC except with RF heating or timber with a moisture content of above 12% Timber which in use will be permanently wet and stressed should be glued with a thermosetting adhesive.

     

    For our full range of filler for wood, please click here. For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it, please visit their website here.

  • Bond-It Lami-Mate Timber Sealant – Box of 12

    £29.34

    Bond-It Lami-Mate Timber Sealant is a polymer enhanced, flexible sealant and gap-filler designed for sealing all tongue and groove laminate flooring. When cured it can be varnished or wood stained if required.

    Uses

    Bond-It Lami-Mate stays permanently flexible and can be used for sealing all types of laminate and hardwood flooring. It can also be used for sealing around timber window and door frames as well as all types of fitted furniture. For example, bedroom and kitchen fittings, laminate worktops etc. LAMI-MATE is also suitable for sealing glass panels into kitchen unit doors. In addition, it is suitable for internal and external use.

    Application

    Apply using a standard sealant gun. Cut the nozzle at a 45° angle with a sharp blade, making sure not to damage the thread.  The nozzle should be cut to an opening slightly larger than the joint tha is to be sealed. Smooth down using a slightly wetted spatula, dampened with a soap & water solution.

    We have a number of tools on our website that would assist with the application of this product. We would recommend using a PC Cox Skeleton Gun to apply & a Bond-it Tooling Kit to aid in providing a professional finish.

    Limitations

    Do not use in conjunction with bitumen or asphalt. For perimeter use only, do not use in areas subject to mechanical abrasion. Furthermore, do not attempt to sand down.
    Caution: The colour on application will be different from the colour achieved when fully cured.

    Container Size

    EU3 plastic cartridge.

    Colours

    LAMI-MATE comes in 4 colours: teak, pine, dark oak and light oak.

    For all other Bond-it products on our website, please click here.

    For similar wood sealants, click here.

    For any further information you may need on Bond-it, please visit their website here.

  • Bond-it WP70 Neutral Cure Oxime Silicone – Box of 12

    £25.50

    Bond-it WP70 Neutral Cure Oxime Silicone is a one-component, professional-grade neutral oxime curing sealing compound.

    Bond-it WP70 is a high quality, neutral cure silicone for perimeter sealing of internal and external door and window frames. Rapid curing with excellent adhesion properties and a higher gloss finish.

    – Permanently elastic
    – Weatherproof
    – Non-fading
    – Suitable for alkaline and metal surfaces
    – Low odour
    – Safe to use
    – Contains additional uPVC adhesion promoters.

    Uses

    For sealing of wood, aluminium and PVCu door and window frames and for weather sealing and flexible jointing of infill panels.

    Preparation

    Ensure all surfaces are dry and free from grease or any contaminants that may hinder adhesion. For best results on movement joints, Bond It EXPANDING FOAM is recommended as a backing material, or a suitable backing tape or rod.

    Application

    All surfaces must be dry and dust and grease-free. Porous materials should be primed for optimum adhesion. Cut the tip of the cartridge, screw-on nozzle and cut at an angle of 45o. Apply at temperatures between +5o C and +45o C using a standard sealant gun. Tool the sealant using the appropriately shaped tooling aid – DO NOT USE A WETTED FINGER.

    Limitations

    Not suitable for use with aquaria. Not suitable for use on bitumen or asphalt. Substrates like marble, sandstone and similar porous surfaces can show a discolouration around the sealant edges. Not suitable for bedding double glazed windows.

    For all other Bond-It products on our website, please click here.

    For any further information you may need on Bond-It, please visit their website here.

  • CT1 Sealant & Adhesive

    £12.95 £10.99

    CT1 Sealant and Adhesive

    The One-Stop Product for all Sealing and Bonding

    CT1 is a construction adhesive that will never shrink or crack and can be structured and painted with any type of paint. Unlike other sealants, CT1 can be applied onto wet surfaces, making it ideal for use underwater in marine projects.

    Due to its ability to work with water, it is also the ideal product to seal baths and shower trays, windows, doors, roofing and guttering. CT1 Sealant and Adhesive is extremely versatile and is often used across multiple different projects by tradespeople. Available in a range of colours, simply select from the drop-down menu: Clear, Black, Brown, Grey, White, Silver, Oak and Beige. For a wide range of internal sealant colours please refer to Mapesil AC.

    As an adhesive, CT1 will create a formidable bond between any substrate, for instance, metals, glass, mirror, fibreglass, plastics, and stone, concrete, the list is endless. CT1 is often the first port of call for a tradesperson looking for a reliable construction adhesive. Above all, the adhesive to use for a multitude of applications is CT1, creating a permanent bond that will resist extreme loads, pressure and tensile strain.

    Order online today, discounts available and trade and credit account options via our website.

  • Dowsil 796 PVC-U Wood Aluminium Silicone – Box of 12

    £43.18

    Dowsil 796 is a one-part, PVC-U, Aluminium & Wood Silicone Sealant. It is a low modulus, neutral cure silicone, specifically developed for the sealing of PVC-U, glass, glazed surfaces and brickwork.

    How to use

    Clean all joints of release agents, water repellents, dust, dirt, old sealants and other contaminants which could impair adhesion.

    Nonporous surfaces should be cleaned by wiping with a suitable solvent such as DOWSIL R40 Universal Cleaner on oil and lint-free cloth.

    Preparation Dowsil 796

    Masking areas adjacent to the joints should be masked with tape to prevent contamination of the substrates and to ensure a neat sealant line. Masking tape should be removed immediately after tooling.

    Primer is not required for PVC-U or most common construction substrates including brick. A test placement before general use is always recommended.

    To ensure a satisfactory seal, the joint should be tooled down within 5 minutes of application before the curing process takes effect.

    This product should be used in conjunction with a standard-sized silicone or caulking gun.

    Please contact Dowsil’s technical service department if you require further assistance

    For all other Dowsil products on our website, please click.

    For any further information you may need on Dowsil products, please visit the Geocel website here.

  • Everbuild Everflex 195 Siliconised Acrylic

    £1.79

     

    Everbuild Everflex 195 Siliconised Acrylic Sealant is a siliconised acrylic sealant, suitable for internal and external use, that provides a permanently flexible long lasting seal which adheres to virtually all materials. Everbuild Everflex 195 has a powerful fungicide to prevent mould growth and improved adhesion characteristics when compared to conventional acrylic sealants.

    USES

    – PVCu profile, trim and cladding.
    – Internal sealing around PVCu window and door frames.
    – Sealing cracks and gaps in brickwork, stone & plaster.
    – An adhesive for bonding polystyrene coving and tiles.
    – An adhesive for bonding cork tiles and wood block flooring.
    – Gap and crack filler prior to decorating.

    CHARACTERISTICS / ADVANTAGES

    – Permanently flexible.
    – Adheres to most surfaces.
    – Mould resistant.
    – Easy cleanup.

    APPLICATION INSTRUCTIONS

    SUBSTRATE PREPARATION

    All surfaces must be clean and dust free. Highly porous surfaces should first be primed with Everbuild PVA bond diluted 1:4 with water.

    APPLICATION METHOD / TOOLS

    Using a shrap knife, cut the tip of the cartridge. Take care not to damage the thread. Apply using a standard sealant gun. Ideally, the joint depth should be half of the width. Smooth down within 20 minutes of application using a wetted spatula or piece of wood. You should take care at this point not to soak the surface because this will delay drying. The product can be overpainted after 60 minutes.

    CLEANING TOOLS

    Any excess sealant can be cleaned away using a sponge dampened in lukewarm water.

    LIMITATIONS

    – Not for use in conjunction with bitumen.
    – Do not attempt to abrade when cured.
    – Can not be used around shower trays.
    – Overpainting is not necessary. However, the product can be painted.

    Note: this product is flexible. Certain inferior quality paints (especially certain vinyl matts) have minimal movement in the dry film. It is possible for the dry paint film to crack if the movement is excessive. Should not be used in a condition of continuous immersion, below ground level, in areas of high abrasion (e.g. floor joints).

    For all other Everbuild products on our website, please click here.

    Any further information you may need on Everbuild products, please visit their website here.

    .

  • Everbuild Lumberjack 550

    £4.58

    Everbuild Lumberjack, 550-floor adhesive is a high spec, hybrid polymer, cartridge or foil pack applied adhesive. It is specially designed for fixing all types of wooden floors directly onto all common building substrates. EVERBUILD® Lumberjack® 550 Floor Adhesive has the following benefits: Free of water & active solvents, so will not cause any warpage. It is also a rapid setting & permanently flexible. Can be used with underfloor heating as it has excellent acoustic properties.

    USES

    Fixing all types of wooden floors onto all common building surfaces.

    CHARACTERISTICS

    Everbuild Lumberjack is free of water & active solvents, so will not cause any warpage or curl to woodblocks/planks.

    – Permanently flexible – compensates for subfloor movement.
    – Will bond wood directly to all common flooring substrates.
    – Due to its high flexibility, it is ideal to use with underfloor heating.
    – Excellent gap filling properties for uneven surfaces
    – Gives unique sound deadening & acoustic properties.

    APPLICATION METHOD / TOOLS

    All installations and subfloor preparations must be carried out in line with the relevant British or international standards. Cut off the tip of sausage and place into a suitable cartridge, then cut off the top of the nozzle flat to leave an 8mm opening. Cut a V-shape down into the nozzle to a depth of around 10mm.

    Fix nozzle and place cartridge into the sealant gun. Hold the gun at 90° to the floor and apply a triangular-shaped bead, approx 8mm wide and 10mm high. Position blocks/planks while the adhesive is still tacky (within 30mins) and taps into final position with mallet and block, removing uncured resin with EVERBUILD WONDER WIPES.

    Floors may be sanded/ trafficked 12-24 hours after application, depending on site conditions (longer at low temperatures).

    If the surface has no or little absorbency; allow three days before sanding/trafficking.

    LIMITATIONS

    – Always refer to the flooring manufacturer re any specific instructions/requirements specifically relating to their flooring before fitting floors.
    – Do not use against substrates that are likely to bleed oils or plasticisers

    VALUE

    All technical data is based on our laboratory tests. However, actual measured data may vary due to circumstances beyond our control.

    ECOLOGY, HEALTH AND SAFETY

    Consult MSDS for the full list of hazards.

    For further information on any Everbuild products, please visit their website here.

  • Everbuild S50 – Box of 25 – Silicone Sealant

    £57.50

    Box of 25

    Everbuild S50 Silicone is a mid-modulus, acetoxy curing silicone sealant that contains a powerful anti-fungal compound to prevent mould and fungal growth in areas of high humidity. Therefore, it gives improved adhesion and flexibility when compared to standard high modulus sanitary grades.

    USES

    – Sealing around all types of baths.
    – Sealing around shower trays.
    – Sealing expansion joints and corners of ceramic tiles.
    – Sealing around most sanitary fittings – check the technical datasheet.
    – Sealing in high humidity areas.
    – Used as an adhesive for bath & shower trim.

    CHARACTERISTICS / ADVANTAGES

    – High viscosity formula for quick, easy tooling.
    – Flexible – movement accommodation of +/- 20%.
    – Waterproof seal.
    – Contains a powerful anti-fungal compound to prevent mould growth. Therefore making it ideal for internal sanitary sealing.

    APPLICATION INSTRUCTIONS

    We have a number of tools on our website that would assist with the application of this product. We would recommend using a PC Cox Skeleton Gun to apply & a Bond-it Tooling Kit to aid in providing a professional finish.

    All surfaces must be dry and clan for application of Everbuild S50. Glass and aluminium should be cleaned with a solvent cleaner before application.

    However, some surfaces may require priming. Therefore a small area should be tested first.

    If the joint is likely to be immersed or if adhesion is weak (especially on porous surfaces) use EVERBUILD SILICONE PRIMER P1. Also, to improve adherence (if required) to non-porous surfaces, prime with EVERBUILD SILICONE PRIMER NP2. LIMITATIONS

    – Do not use in conjunction with Bitumen or Asphalt, use Everbuild Weather Mate.
    – Do not use on anodised or chrome-plated shower trims, use Everbuild 450.
    – It is the user’s responsibility to determine suitability for use.
    – Not to be used on natural stone, as S50 is not anti leaching and will stain after time.

    Always refer to the technical datasheet or speak to someone at Sealant Supplies for advice.

  • Everbuild S50 Silicone Sealant

    £3.99

    Everbuild S50 Silicone is a mid-modulus, acetoxy curing silicone sealant that contains a powerful anti-fungal compound to prevent mould and fungal growth in areas of high humidity. Therefore, it gives improved adhesion and flexibility when compared to standard high modulus sanitary grades.

    USES

    – Sealing around all types of baths.
    – Sealing around shower trays.
    – Sealing expansion joints and corners of ceramic tiles.
    – Sealing around most sanitary fittings – check the technical datasheet.
    – Sealing in high humidity areas.
    – Used as an adhesive for bath & shower trim.

    CHARACTERISTICS / ADVANTAGES

    – High viscosity formula for quick, easy tooling.
    – Flexible – movement accommodation of +/- 20%.
    – Waterproof seal.
    – Contains a powerful anti-fungal compound to prevent mould growth. Therefore making it ideal for internal sanitary sealing.

    APPLICATION INSTRUCTIONS

    SUBSTRATE PREPARATION

    All surfaces must be dry and clan for application of Everbuild S50. Glass and aluminium should be cleaned with a solvent cleaner before application.

    However, some surfaces may require priming. Therefore a small area should be tested first.

    If the joint is likely to be immersed or if adhesion is weak (especially on porous surfaces) use EVERBUILD SILICONE PRIMER P1. Also, to improve adherence (if required) to non-porous surfaces, prime with EVERBUILD SILICONE PRIMER NP2. LIMITATIONS

    – Do not use in conjunction with Bitumen or Asphalt, use Everbuild Weather Mate.
    – Do not use on anodised or chrome plated shower trims, use Everbuild 450.
    – It is the user’s responsibility to determine suitability for use.
    – Not to be used on natural stone, as S50 is not anti leaching and will stain after time.

    We have a number of tools on our website that would assist with the application of this product. We would recommend using a PC Cox Skeleton Gun to apply & a Bond-it Tooling Kit to aid in providing a professional finish.

    Always refer to the technical data sheet or speak to someone at Sealant Supplies for advice.

  • Gorilla 100% Silicone Sealant

    £24.00

    Gorilla 100% Silicone Sealant is great for kitchen, bath, window, doors, plumbing, gutters and more! Ready for water exposure in just 30 minutes, this sealant is mold & mildew resistant and won’t yellow, shrink or crack over time!

    • 100% waterproof for interior and exterior use
    • Mould & mildew resistant
    • Multi-purpose sealant
    • Shrink and crack proof
    • 30 minutes shower ready

    Warning, always read the label.

Laminate Sealant

Our range of branded laminate sealants provide solutions for both trade and domestic projects. The sealants we stock are able to work with a variety of materials, including laminate flooring, oak flooring and any other timber-based material with a requirement for sealing.

We currently stock a vast range of products at different price points; therefore, we have something for each project type. Whether you are a DIY novice or a flooring specialist, we have a laminate sealant to suit your requirements.

Alongside our laminate sealants we also stock a range of sealant accessories and tools, which can be ordered directly via our website. We also specialise in trade and bulk ordering of sealant products.

If you are a trade specialist, we also provide the option to create a trade or credit account with us. Account holders benefit from ongoing discounts and benefits including offers on bulk or repeat orders. More information can be found about our account options via our website.

If you would like to speak to a member of our team about the laminate sealants we stock, do not hesitate to get in touch with us. Simply call our team on 01708 525866 or email info@sealantsupplies.co.uk and we will respond as soon as possible.