Marine & Motor Trade

• 

  Bond-It HA6 RVT Marine Silicone – Box of 25

  £73.00

  Bond-It HA6 RVT Marine Silicone is marine quality, automotive silicone sealant. It is unaffected by saltwater immersion and extreme temperature. This product is non-slumping in paste form.

  Uses

  It is ideal for use on:
  – Glass
  – Ceramics
  – Anodised aluminium
  – Primed metals and timber
  – Many plastics

  Preparation

  Ensure all surfaces are dry and free from grease, oil or any other contaminants that may hinder adhesion.

  Application

  Apply Bond-It HA6 using a standard sealant gun. Cut the nozzle at a 45° angle with a sharp blade, making sure not to damage the thread. The nozzle should be cut to an opening slightly larger than the joint to be sealed. For sealing and bedding apply in the usual fashion and tool to a smooth finish one or two minutes after gunning. As an adhesive, bring the two surfaces together before skinning commences and do not stress the joint before the silicone has developed strength. Clean away any excess with white spirit.
  When using in aquarium assembly, please refer to separate sheet for instructions which can be downloaded from our website.

  For all other Bond-it products on our website, please click here.

  For any further information you may need on Bond-it, please visit their website here.

  For alternative products please see below, options like CT1 are available.

  Select options

  View Details
• 

  CM SFS Stain Free Silicone

  £5.85

  CM SFS Stain Free Silicone is a moisture-cured one-component neutral silicone sealant used mainly for building and glazing joints. With it moisture cure allowing it to cure at room temperature, producing a flexible seal. CM SFS Stain Free Silicone adheres to most common building surfaces without the need for primer. Fully cured movement capability of -/+50%.

  Typical Uses

  CM SFS is designed for jointing or bonding in building and glazing applications such as:

  • Precast panels and curtain wall expansion joints.
  • Windows or doors perimeter joints
  • Aluminium, wood, UPVC glazing joints.
  • Roofs and chimney joints.
  • Venting or gutter joints
  • Bonding mirrors
  • Kingspan panels

  Limits of Use

  • CM SFS is not recommended for use on materials where migration of constituents can take place, e.g. certain rubbers.
  • Not be used for jointing aquariums or swimming pools. Not ideal for permanent immersion.
  • CM SFS, once cured, should not be painted (poor coverage and adhesion of paint).
  • CM SFS is not recommended where abrasion or physical abuse will be encountered.
  • CM SFS must not be used for food contact.
  • When in contact with alkyd paints a slight yellowing can appear on the surroundings of the joint.

   

  Please see the attached datasheet for more information on CM SFS Stain Free Silicone.

  Select options

  View Details
• 

  CT1 Sealant & Adhesive

  £12.95 £10.99

  CT1 Sealant and Adhesive

  The One-Stop Product for all Sealing and Bonding

  CT1 is a construction adhesive that will never shrink or crack, and it can be structured and painted with any type of paint. When applying conventional sealants, the surfaces have to be dry. As a sealant, CT1 can be applied onto wet surfaces, even underwater.

  It is also the perfect product to seal baths and showers, windows, doors, roofs, gutters, virtually anything. Available in a range of colours, simply select from the drop-down menu: Clear, Black, Brown, Grey, White, Silver, Oak and Beige. For a wide range of internal sealant colours please refer to Mapesil AC.

  In other words, it is the only product on the market that is 100% ecologically compliant. As an adhesive, CT1 will create a formidable bond between virtually any materials also acting as a construction adhesive that will successfully bond all building materials. For instance, metals, glass, mirror, fibreglass, plastics, and stone, concrete, the list is endless.

  Above all, the adhesive to use for a multitude of applications is CT1, creating a permanent bond that will resist extreme loads, pressure and tensile strain.

  Will successfully bond

  • Polystyrene
  • Metals (including lead)
  • Glass – Special mirror adhesive can be found here.
  • Mirrors
  • All Woods
  • Plastics (excluding Polypropylene)
  • Fibreglass
  • Tiles
  • Concrete
  • Most Stones (without staining)
  • Most Synthetic Materials

  Unique adhesion on virtually any material in most applications without the need for additional fixings. Therefore, CT1 is the ultimate solution for interior and exterior bonding and sealing.

  • Excellent resistance to chemicals
  • UV resistant
  • Perfect for marine and boating maintenance, accident and emergency repairs
  • Odourless
  • Does not shrink
  • Can be painted
  • Contains no solvents
  • No isocyanates
  • Unique flexibility
  • 8 colours to choose from Black, Brown, Grey, White, Oak, Clear, Beige and Silver. For further information on this product, please visit the CT1 website here.

  Select options

  View Details
• 

  EB25 Ultimate Sealant & Construction Adhesive – Box of 12

  £143.76

  EB25 has been launched in 2019 to celebrate their 25 years of Everbuild.

  EB25 is the Ultimate Sealant and Adhesive, covering the broadest range of application, sealant and adhesive areas. It is a polymer blend sealant giving it additional flexibility and bonding strength you can rely on in any situation. The makeup of this product allows the sealant to be used both internally and externally, in most weather conditions and can be used underwater. Everbuild have had EB25 certified for use in sanitary and food preparation areas and once cured is resistant to mould, temperature extremes, chemicals and more

  Colours – Black, White and Grey. Also, Crystal Clear that remains crystal clear and does no fog like similar products.

  Substrates that EB25 bonds to:

  • Metal
  • Wood
  • Brick
  • Concrete
  • Stone
  • Ceramic
  • Tile
  • Plastic
  • Glass

  PRODUCT DESCRIPTION

  Everbuild brings you their best ever sealant and adhesive – EB25, to celebrate their 25th anniversary. Using the most cutting-edge technology and an exclusive polymer blend, our R&D team has developed a truly universal, top quality hybrid. Therefore, it is incredibly flexible, certified for indoor and outdoor use, and in sanitary and food preparation areas (ISEGA). Plus, it’s powerful, sticks to just about anything and even works when applied underwater! Once cured, it’s resistant to mould, temperature extremes, chemicals, petrol, UV radiation, plus it does all this while being environmentally friendly.

  USES

  Bonding & sealing in almost every application imaginable. The following are just some examples: As a high-quality nail replacement adhesive, even to damp surfaces.

  – External and internal pointing around doors and windows.
  – Bonding mirrors to most common substrates.
  – Sealing vertical expansion joints.
  – Jointing cladding panels.

  SUBSTRATE PREPARATION

  All surfaces must be clean and dust-free. Surfaces may be damp but have no standing water. Therefore, it can be used underwater, but adhesion performance is reduced so should be applied as an emergency repair in these conditions only.

  ---

  For all other Everbuild products on our website, please click here. For general sealing, please see our DIY section and select the area you require.

  For any further information you require on Everbuild products, please visit their website here.

  This product is Everbuild’s equivalent of the CT1 range and can be used like for like.

  ---

   

  Select options

  View Details
• 

  Everbuild Everflex 175 Universal Acrylic Sealant

  £2.60 £1.51

  Everbuild Everflex 175 is a sealant that is acrylic based & suitable for internal and external use. It provides a flexible long lasting seal that adheres to virtually all materials. In addition, Everbuild Everflex 175 can be overpainted.

  USES

  – PVCu profile, trim and cladding.
  – Internal sealing around PVCu window and door frames.
  – Sealing cracks and gaps in brickwork, stone and concrete.
  – Gap and crack filler before decorating.
  – Sealing around baths and basins.

  CHARACTERISTICS / ADVANTAGES

  – Permanently flexible
  – Mould resistant.
  – Overpaintable.
  – Easy cleanup.

  APPLICATION INSTRUCTIONS

  SUBSTRATE PREPARATION

  All surfaces must be clean and dust free. All flaking or loose surface coatings should be removed as should any old mastic before application. Highly porous substrates should be primed before application with Everbuild PVA bond diluted 1:4 with water.

  APPLICATION METHOD / TOOLS

  Using a sharp stanley blade, cut the tip of the cartridge, taking care not to damage the thread. Apply nozzle and again, cut cleanly at a 45° angle, with the opening being slightly larger than the gap to be sealed. Apply product using a standard sealant gun.

  LIMITATIONS

  – Not for use in conjunction with bitumen or asphalt.
  – Do not attempt to abrade when cured.
  – Do not use around shower trays. Use GENERAL PURPOSE SILICONE for greater movement capabilities
  – Overpainting is not necessary.

  Note: this product is flexible. Certain inferior quality paints (especially certain vinyl matts) have very little movement in the dry film. However, it is possible for the dry paint film to crack if the movement is excessive.

  For all other Everbuild products on our website,  please click here.

  Any further information you may need on any Everbuild products, visit their website here.

   

  Select options

  View Details
• 

  Everbuild Puraflex 40 310ml

  £4.08

  Everbuild Puraflex 40 is a one-part component, high modulus PU sealant and adhesive which adheres firmly to most substrates. Provides excellent
  mechanical resistance &  resistance to most common chemicals. Furthermore, this product can be over-painted when cured.

  USES OF EVERBUILD PURAFLEX 40

  – Sealing and bonding metal panels and trim.
  – Expansion joint sealing in concrete panels and floor joint.
  – A wide number of sealing and bonding jobs in the construction and engineering markets.
  – Bonding in container fabrication.
  – Heavy traffic floor joints such as those found in warehouses, garage floors, factory floors, sports arenas & shopping centres etc.

  CHARACTERISTICS / ADVANTAGES

  – Bonds to most building substraes, such as concrete, wood, metal, aluminium, polyester, glass, u PVC, stone, ceramics, etc
  – Can be overpainted with gloss and emulsion.
  – Good sea water resistance.
  – You can paint over this product, once cured, with oil and latex paints.

  APPLICATION INSTRUCTIONS

  SUBSTRATE PREPARATION FOR EVERBUILD PURAFLEX 40

  Before application, please ensure all surfaces are clean, dry and dust free before using Everbuild Puraflex 40. All old sealant and mastic joints should be removed before application. In addition to that, when using on glass, metal and aluminium, areas should be cleaned using a solvent cleaner before application for optimum adhesion. When using Everbuild Puraflex 40 with solvents, always ensure adequate ventilation. Avoid heat, sparks and open flames. Observe and follow all precautions listed on the solvent container label. It is not recommended for application to surfaces that are below 5˚C as it is impossible to guarantee a dry, frost-free surface at these temperatures, therefore the sealant will most likely fail. It is unlikely that priming will be required, however, concrete must be sealed using a Primer. After that, if you are in doubt consult Technical Services.

  PRIMER

  On porous substrates like concrete use Sika Primer – 3N.

  LIMITATIONS

  – Not for use on substrates that could bleed solvents or plasticises.
  – Do not use on bitumen or asphalt.
  – Paint types vary so conduct a trial prior to full application. Some paints have low movement and can show surface cracking.

  In addition to the above, if you require further information on this product, you can visit the Everbuild website here.

  This product is also available in a 600ml foil & can be viewed here.

  Select options

  View Details
• 

  Gorilla Epoxy 25ml

  £6.25 £4.40

  Gorilla Epoxy 25ml takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the resin and hardener separate, so it is easy to dispense and won’t harden over time.

  The two-part, gap-filling formula easily bonds steel, aluminium, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless.

  Gorilla Epoxy 25ml Features

  • Gorilla strong–incredible performance for the toughest jobs
  • Dries crystal clear–ideal for clean, easy finishing
  • Five-minute set–plenty of repositioning time for the perfect fit
  • Gap filling–fills voids and bonds uneven and vertical surfaces
  • Superior water resistance–withstands moderate exposure to water
  • Easy to use syringe–separate barrels of resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses
  • Solvent resistant–will not break down from exposure to common solvents
  • Low VOC and non-toxic once cured–safe for everyday handling

  Warning, always read the label.

  Add to basket

  View Details
• 

  GorillaWeld Heavyweight Epoxy

  £5.25

  GorillaWeld Heavyweight Epoxy is an incredibly strong, heavy duty two-part adhesive. The tough, steel bond epoxy formula has a 4250 PSI bond strength and sets in just 10 minutes. GorillaWeld is waterproof and versatile, creating a long-lasting, permanent bond to metal, plastics*, concrete, ceramics, PVC, fibreglass and more!

  • INCREDIBLY STRONG: 4250 PSI
  • STEEL BOND EPOXY
  • SETS IN 10 MINUTES
  • WATERPROOF*
  • FORMS PERMANENT BOND
  • DRIES DARK GRAY
  • EASY TO USE
  • BONDS: Metal, Plastic**, Concrete, PVC, Fiberglass, Ceramic & More!

  Warning, always read the label.

   

  * Bonded wood materials should not be submerged or soaked in water

  ** Not recommended for use polyethene or polypropylene plastics.

  Add to basket

  View Details
• 

  Sika Sikabond AT Metal – Box of 12

  £108.00

  Sika Sikabond AT Metal is a one-part, solvent-free, elastic adhesive and sealant for porous and non-porous substrates, particularly for metals. Sika Sikabond AT Metal is based on Silane Terminated Polymers.

  USES

  Sikabond AT Metal has strong adhesion on non-porous substrates, especially on metals (aluminium, copper, galvanised steel, stainless steel, etc.), and many plastics (PVC, powder coatings, etc.)

  CHARACTERISTICS / ADVANTAGES

  – 1-part, ready to use
  – Excellent adhesion without priming on many metals and non-porous substrates
  – Excellent adhesion on porous substrates (i.e. concrete, roof tiles, mortar etc.)
  – Excellent work-ability
  – Short cut off string
  – Good initial tack and fast curing
  – Non-corrosive
  – Good weathering and water resistance
  – Silicone free
  – Solvent-free

  APPLICATION METHOD / TOOLS

  Sikabond AT Metal is supplied ready to use. After substrate preparation applies Sika Sikabond AT Metal in beads, strips or spots on the bonding surface at intervals of a few centimetres.

  NOTES ON APPLICATION  / LIMITATIONS

  Sika Sikabond AT Metal is not to be used for Facade panel bonding. For facade panels use the SikaTack-Panel System. Also,
  do not use SikaBond AT-Metal as a glass sealer, on titan zinc, bitumin substrates, natural rubber, EPDM rubber or on building materials which might bleed oils or solvents. However, for the correct curing of the adhesive sufficient relative humidity is necessary.
  Elastic adhesives should not generally be overpainted. If there is overpainting of the adhesive, surface cracking and higher tackiness plus slight colour variations can occur.

  For all other Sika products on our website, please click here.

  Any further information you may need on Sika products, please visit their website here.

  Select options

  View Details
• 

  Sika Sikaflex 221

  £8.95 £6.25

  Sika Sikaflex 221 is a high-quality multi-purpose non-sag, polyurethane sealant that cures on exposure to atmospheric humidity to form a durable elastomer.

  PRODUCT BENEFITS

  – 1-C formulation
  – Elastic
  – Low odour
  – Resistant to ageing
  – Non-corrosive
  – Can be painted
  – NSF-approved for incidental food contact.

  CHEMICAL RESISTANCE

  It is temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils. However, it is not immune to organic acids, alcohol, concentrated mineral acids and caustic solutions or solvents. Furthermore, any advice on specific applications will be given on request.

  METHOD OF APPLICATION

  Surface preparation

  Surfaces must be free from all traces of grease and dust.
  Above all, if you need any advice on specific applications, then contact the Technical Service Department of Sika Industry.

  Over-painting

  The paint must be tested for compatibility by carrying out preliminary trials, and the best results are obtained if the sealant is allowed to cure thoroughly first, especially in the case of baked enamels. Therefore, please note that non-flexible paint systems may impair the elasticity of the adhesive, impair joint movement and lead to cracking of the paint film.

  PVC based paints and paints that dry by oxidation (oil or alkyd resin-based) are generally not suitable for application over Sikaflex -221.

  For all other Sika products on our website, please click here.

  For any further information you require on Sika products, please visit their website here.

  Select options

  View Details
• 

  Soudal Aquafix – All Weather Sealant

  £3.25

  Soudal Aquafix is an all-weather sealant is an adhesive sealant that bonds to most surfaces even when damp or underwater. Ideal for use in emergency repairs or as a general sealant, Aquafix can be overpainted after curing and is UV resistant. Universal and can be used in many different areas for different application types, from sealing to adhering, it is an all-round sealant.

  Applications for Aquafix:

  We have a number of tools on our website that would assist with the application of this product. We would recommend using a PC Cox Skeleton Gun to apply & a Bond-it Tooling Kit to aid in providing a professional finish.

  • All usual building substrates including Wood, Metals, Polycarbonate, Plastics, Brick, Concrete, MDF and Glass.*
  • Repair of leaks.
  • UV Resistant.

  * Do not apply to PVC, PE, PP, PTFE and Bituminous substrates.

  Benefits of Aquafix:

  • Easy to apply and tool
  • Solvent Based
  • Adheres underwater
  • Good slump resistance
  • 10% Movement Accommodation

  Select options

  View Details
• 

  Soudal Fix All – Scratch To Win a Ford Ranger Competition

  £17.28 – £18.72

  Soudal (UK) Ltd are allowing you to WIN a Ford Ranger Double Cab Wildtrak.

  How to Enter the Draw

  We are excited to announce the launch of our latest Fix ALL promotion!! Be in with a chance to WIN a Ford Ranger Wildtrak when you buy a Fix ALL Crystal or Fix ALL High Tack promotional 6-pack!! There is a scratchcard in every box!!

  Forty thousand scratchcards with their own unique code have been produced and randomly placed into thousands of 6-pack boxes of Fix ALL Crystal and thousands of 6-pack boxes of Fix ALL High Tack White.
  Visit www.soudal.eu/FordRangerPromotion and enter your details and unique scratchcard code (inside every promotional box) online before 11:59 pm on the 30/03/2020.
  You are welcome to enter the competition multiple times, providing that each entry is a legitimate purchase. On the 31st March 2020, the winners code will be drawn totally at random.

  Who can enter?

  Entry is welcome to residents of the UK and Republic of Ireland & all entrants must be aged 18 years or above. This excludes the following –

  1. Employees of business’ participating in the promotion, employees or agency staff working for the promoting company associated with the competition.
  2. A spouse, partner, parent, guardian, sibling or child of a person referred to within the above paragraph.
  3. Anyone that is in breach of the competition terms and conditions of this promotion. Soudal holds the right for determining the eligibility of entrants into the draw.

  Where?

  This competition will run in participating stores throughout the UK & Republic of Ireland.

  Do I Need to Make a Purchase?
  

  Yes. During the promotion period, you will need to purchase either a Fix ALL High Tack Promo 6-Pack or Fix ALL Crystal Promo 6-Pack and retain your receipt as proof of purchase.
  You must keep your receipt to qualify for the prize draw. Soudal may disqualify your entry if you are unable to provide proof of purchase, and you will then lose any right to receive the prize.

  The Prize Draw

  The draw will be held on the 31st of March 2020. The 1st valid entry to be drawn will be the winner.
  Additional reserve entries may be drawn just in case the winning entry is deemed invalid.
  The winner will be contacted within one month of the deadline by phone and writing.
  If the winner cannot be contacted via the contact information provided, Soudal reserves the right to select the next reserve entry; this will occur one month following the first contact.

  The Winner

  The winner must make sure they are available to attend all publicity, photography and other marketing activities as required by Soudal and Seal Systems Ireland. You allow Soudal and Seal Systems Ireland to use your name and image in any advertising or promotional event. You must be available for the presenting of the Ford Ranger Wildtrak in April 2020.

  For all other Soudal products on our website, please click here.

  Soudal FixAll is Soudal’s rival to the CT1 range, both excellent options for Adhesive and sealing.

  Select options

  View Details