Total: £0
(Price shown excludes VAT)Total: £0
(Price shown excludes VAT) (Price shown excludes VAT) (Price shown excludes VAT)
CM Sealants
CM 200 PF Fast Cure
£55.00CM 200 PF Fast Cure
CM200 PF Fast Cure is a two-part sealant that is used for several sealing areas. Most commonly used for sealing expansion joints, due to the advantages of the CM 200 PF it can be used for sealing joints in concrete paved areas, docks, container depots, industrial factories, warehousing petrol forecourts. CM200 PF can be cold applied, so ideal for small works, such as remedial re-sealing of joints.
Advantages
- High-performance good movement accommodation, tolerant of severe climatic conditions.
- Chemical Resistant to spillages of fuels, hydraulic fluids, synthetic and mineral oils, and dilute acids and alkalis.
- Hand pour or machine/sealant gun application to joint.
- Non-Toxic Sealant.
- ISO 9002 Quality Assured Firm -BS5212. 1990 Type N – ISO 11600-F-25LM
- High Adherence
- Cure Time 20 to 30 mins.
Cure Time
The life of the tin is 20 to 30 minutes at 25C, this is affected, but the outside temperature and the sealant temperature. Final cure, when full working properties are developed, occurs within two days at 25C, although the sealant will normally bear traffic within 2 hours of application. Higher temperature will result in a faster cure time; low temperatures will result in longer cure time. Do not apply at temperatures below 4C.
Preparation
Ensure that the joint is clean, free from dust and dirt. The joint should also be dry; any contaminant should be removed, the previous sealant, if re-sealing is taking place, must all be removed. If you are backing the joint with backer foam strip, ensure the backer strip is bonded to the base of the joint and proceed to apply. Priming of the surface should be done once the joint is cleaned, the joint faces should be primed with the appropriate primer. CM Primer C is recommended.
CM 200 PF Mixing and Application
Open Pack B and empty the contents into Pack A – Stir for five minutes, preferably using a slow speed electric drill with a mixer paddle, the mix is one. Take care to avoid including excess air. Pour or gun apply immediately into the primed joint. Current practice requires that the sealant shall be poured to a level between 3mm (Summer) and 6mm (Winter) below the wearing concrete surface.
CM Bath & Kitchen HM
£5.99Details:
CM Bath & Kitchen is a high modulus silicone sealant that cures rapidly once exposed to natural humidity. Once cured, CM Bath & Kitchens forms to create a permanently flexible, durable sealant which is ideal for use within bathroom and kitchen environments.
CM Bath & Kitchen is also suitable for use in a range of temperature environments, weathering extremely well and providing a reliable seal in joints. CM Bath & Kitchen is a premium silicone sealant product available in a range of colours, used for exceptional finishes.
CM Bath & Kitchen meets the standards to BS5889 (1989) Type B and US Fed Spec TTS 001543A (Class A) and TTS 00230C (Class A) and ISO 11600 F&G -25HM 846 food safe.
Uses:
The uses of CM Bath & Kitchen are but not restricted to the below:
- Joints in baths and showers
- General kitchen areas
- Food prep areas
- Laboratories
- High hygiene areas
- Construction Joints
- Swimming pools
- Glass, ceramic or painted surfaces
Application:
Before the application the required area must be cleaned, dust free, contaminate free, and no loose objects are present. If you wish to prime before use, standard primer is advised. If you are re-sealing joints, it is advised that every bit of old sealant is removed to ensure that the joint is contaminant free.
To apply, cut off the top of the cartridge, ensuring it is above the nozzle thread, proceed to screw the nozzle and snipping the top of the nozzle to required joint size at a 45-degree angle. Apply the sealant by gun – place the nozzle angle flush to the joint and extrude a continuous bead. For a neat finish, use a sealant applicator tool kit.
CM Primer C – 1L
£19.00CM Primer C is a single component, solvent-borne, polyurethane priming coat to be used with CM200 PF.
Typical Uses
CM Primer C is suitable for priming dry, porous surfaces which form the bonding face of an expansion or construction joint.
- To be used on concrete,
- To be used on cementitious or epoxy mortars,
- To be used on timber
- To be used on porous stone surfaces.
Do not use on glazed, metallic or sealed surfaces (e.g. G.R.P. polished stone, painted surfaces etc.)
Priming
Once the joint is clean, the joint faces should be primed with CM Primer C using a small paintbrush, ensure that the faces are completely covered. After priming, allow half an hour for the solvent to evaporate. If the application of the sealant is delayed for more than 2 hours after priming, joints should be reprimed.
Handling
- Primer C contains a moisture curing urethane and a hydrocarbon solvent.
- Harmful – wear PPE when handling, follow safety precautions if inhalation or swallowing.
- PPE suggestion – suitable gloves and eye/face protection.
- Do not breathe fumes.
- Keep away from sources of ignition.
CM SFS Stain Free Silicone
£5.85CM SFS Stain Free Silicone is a moisture-cured one-component neutral silicone sealant used mainly for building and glazing joints. With it moisture cure allowing it to cure at room temperature, producing a flexible seal. CM SFS Stain Free Silicone adheres to most common building surfaces without the need for primer. Fully cured movement capability of -/+50%.
Typical Uses
CM SFS is designed for jointing or bonding in building and glazing applications such as:
- Precast panels and curtain wall expansion joints.
- Windows or doors perimeter joints
- Aluminium, wood, UPVC glazing joints.
- Roofs and chimney joints.
- Venting or gutter joints
- Bonding mirrors
- Kingspan panels
Limits of Use
- CM SFS is not recommended for use on materials where migration of constituents can take place, e.g. certain rubbers.
- Not be used for jointing aquariums or swimming pools. Not ideal for permanent immersion.
- CM SFS, once cured, should not be painted (poor coverage and adhesion of paint).
- CM SFS is not recommended where abrasion or physical abuse will be encountered.
- CM SFS must not be used for food contact.
- When in contact with alkyd paints a slight yellowing can appear on the surroundings of the joint.
Please see the attached datasheet for more information on CM SFS Stain Free Silicone.
CM Stonesil
£5.50CM Stonesil is an elastic single-component silicone sealant for indoor and outdoor use, with up to 50% movement tolerance.
Uses and Application Areas
- Low modulus non-staining sealant with anti-fungal properties.
- Fast cure rate.
- Outstanding UV, weather, and ageing resistance.
- Adhesion to numerous substrates, such as granite, composite stones, ceramic tiles, brickwork, metals, plastics also compatible with copper.
- Low modulus (conforms to ISO 11600 F&G 25 LM).
- Movement capability up to 50% (ASTM C920 class 50).
- Non-staining (ISO 16938-1, ASTM C 1248).
- Sealing joints in premier bathrooms & kitchens.
- Glass to glass joints.
- Sealing glass to metal.
- Expansion joints in brickwork/stonework.
- Marine applications.
Joint dimensions
The minimum joint size suggested is 5mm x 5mm for internal use and external use 10mm x 8 mm (width x depth). Maximum recommend width of the joint is 30mm x 30mm, but the joint depth should be roughly half the joint width for the ideal seal.
Tooling
After applying the sealant, it can be smoothed in the joint with water or with a neutral, non-staining water-based smoothing agent and a suitable tool (e.g., Bond-It Applicator Kit). Smoothing the sealant isn’t just recommended for aesthetic reasons, but it will assist in the bonding of the sealant to the substrate.
Foam Strip 12mm x 12mm x 100m
£13.50Sealant Polyethylene Backer Strip 12mm x 12mm x 100m
Non-absorbent compressible white closed cell polyethene foam backup material. Insert into a joint to control sealant depth & create a backstop. Strip of 100m of 12mm x 12mm square polyethene foam joint filler and backing for sealants and acoustic applications. Compatible with all know types of sealants to control the depth of the sealant in proper relation to joint width. Provides backing against which the sealant is applied, forcing the sealant to the sides of the joint for adhesion.
Choosing the correct size:
Select a backer strip width that is approximately between 15 and 25% larger than the width of the joint to give a firm base. The backer strip can be compressed down into gaps slightly tighter than its width.
Applications:
- General Purpose Sealant backing
- Together with Self-leveling sealant
- Expansion Joints
- Irregular joints
- Metal and pre-cast panels
- Around perimeters of door and window frames
- Coping and glazing joints
- Log Cabins / Homes
- Draft Proofing & Acoustic Work
Also, we provide the backer foam in rods or rolls in all sizes, 13mm and 10mm backer rod equivalent. Fire protective backer foam is also available here.
Foam Strip 15mm x 12mm x 100m
£16.99Sealant Polyethylene Backer Strip 15mm x 12mm x 100m
Non-absorbent compressible white closed cell polyethene foam backup material. Insert into a joint to control sealant depth & create a backstop. Strip of 100m of 12mm x 12mm square polyethene foam joint filler and backing for sealants and acoustic applications. Compatible with all know types of sealants to control the depth of the sealant in proper relation to joint width. Provides backing against which the sealant is applied, forcing the sealant to the sides of the joint for adhesion.
Choosing the correct size:
Select a backer strip width that is approximately between 15 and 25% larger than the width of the joint to give a firm base. The backer strip can be compressed down into gaps slightly tighter than its width.
Applications:
- General Purpose Sealant backing
- Together with Self-leveling sealant
- Expansion Joints
- Irregular joints
- Metal and pre-cast panels
- Around perimeters of door and window frames
- Coping and glazing joints
- Log Cabins / Homes
- Draft Proofing & Acoustic Work
Also, we provide the backer foam in rods or rolls in all sizes, please click here for the 15mm backer rod equivalent. Fire protective backer foam is also available here.
Foam Strip 20mm x 12mm x 100m
£17.00Sealant Polyethylene Backer Strip 20mm x 12mm x 100m
Non-absorbent compressible white closed cell polyethene foam backup material. Insert into a joint to control sealant depth & create a backstop. Strip of 100m of 12mm x 12mm square polyethene foam joint filler and backing for sealants and acoustic applications. Compatible with all know types of sealants to control the depth of the sealant in proper relation to joint width. Provides backing against which the sealant is applied, forcing the sealant to the sides of the joint for adhesion.
Choosing the correct size:
Select a backer strip width that is approximately between 15 and 25% larger than the width of the joint to give a firm base. The backer strip can be compressed down into gaps slightly tighter than its width.
Applications:
- General Purpose Sealant backing
- Together with Self-leveling sealant
- Expansion Joints
- Irregular joints
- Metal and pre-cast panels
- Around perimeters of door and window frames
- Coping and glazing joints
- Log Cabins / Homes
- Draft Proofing & Acoustic Work
Also, we provide the backer foam in rods or rolls in all sizes, please click here for the 20mm backer rod equivalent. Fire protective backer foam is also available here.
Foam Strip 25mm x 12mm x 100m
£21.50Sealant Polyethylene Backer Strip 25mm x 12mm x 100m
Non-absorbent compressible white closed cell polyethene foam backup material. Insert into a joint to control sealant depth & create a backstop. Strip of 100m of 12mm x 12mm square polyethene foam joint filler and backing for sealants and acoustic applications. Compatible with all know types of sealants to control the depth of the sealant in proper relation to joint width. Provides backing against which the sealant is applied, forcing the sealant to the sides of the joint for adhesion.
Choosing the correct size:
Select a backer strip width that is approximately between 15 and 25% larger than the width of the joint to give a firm base. The backer strip can be compressed down into gaps slightly tighter than its width.
Applications:
- General Purpose Sealant backing
- Together with Self-leveling sealant
- Expansion Joints
- Irregular joints
- Metal and pre-cast panels
- Around perimeters of door and window frames
- Coping and glazing joints
- Log Cabins / Homes
- Draft Proofing & Acoustic Work
Also, we provide the backer foam in rods or rolls in all sizes, please click here for the 25mm backer rod equivalent. Fire protective backer foam is also available here.
Foam Strip 30mm x 12mm x 100m
£26.50Sealant Polyethylene Backer Strip 30mm x 12mm x 100m
Non-absorbent compressible white closed cell polyethene foam backup material. Insert into a joint to control sealant depth & create a backstop. Strip of 100m of 12mm x 12mm square polyethene foam joint filler and backing for sealants and acoustic applications. Compatible with all know types of sealants to control the depth of the sealant in proper relation to joint width. Provides backing against which the sealant is applied, forcing the sealant to the sides of the joint for adhesion.
Choosing the correct size:
Select a backer strip width that is approximately between 15 and 25% larger than the width of the joint to give a firm base. The backer strip can be compressed down into gaps slightly tighter than its width.
Applications:
- General Purpose Sealant backing
- Together with Self-leveling sealant
- Expansion Joints
- Irregular joints
- Metal and pre-cast panels
- Around perimeters of door and window frames
- Coping and glazing joints
- Log Cabins / Homes
- Draft Proofing & Acoustic Work
Also, we provide the backer foam in rods or rolls in all sizes, please click here for the 30mm backer rod equivalent. Fire protective backer foam is also available here.
CM Sealants
Providing a variety of sealants and accessories, CM Sealants are a highly requested brand by our customers throughout the UK.
From primers, stain free silicone and Bath and Kitchen silicone, through to foam strips, CM Sealants have a huge range of products which can be utilised by tradespeople in a number of project types.
We often recommend CM Sealants for projects where a reliable and cost-effective sealant is required. These products are also ideal for DIY projects, especially the Kitchen and Bath sealants which are easy to use and available in a range of colours. CM Sealants have also been rigorously tried and tested under food safety standards therefore are suitable for use in both home and commercial kitchens.
This sealant brand take pride in the high-quality solutions they provide. Sealants from CM are flexible, watertight and rapidly cure when exposed to natural humidity. Their sealants also have the ability to withstand changing temperatures and weathering.
CM Sealants provide solutions for both interior and exterior projects, covering a huge range of basis so there is something for everyone. Available at cost-effective prices, the CM Sealants we stock provide a solution for a variety of project types.
If you have any questions on the sealants we stock or how to make a bulk order, do not hesitate to get in touch with our friendly team. Simply call 01708 525 866 to speak to a member of our team.
Shop by brand
