Fosroc

• 

  FOSROC Colpor 200PF (Box of 2)

  £120.00 £100.00

  Fosroc Colpor 200PF

  Fosroc Colpor 200PF is a two-part polyurethane sealant designed for joints in concrete paved areas. The capability of accommodating cyclic movements is retained by Colpor 200 throughout extremes of temperature conditions. Fosroc Colpor is resistant to oil and hydraulic fluid spillage, something which could be detrimental to other external flooring sealants.

  It will not harden in cold weather nor become excessively soft or pick up in hot condition, making it ideal for use in a range of environments and climates. Furthermore, Colpor 200PF has high durability and long service life which reduces maintenance costs.

  USES

  For the horizontal sealing and maintenance of joints in concrete roads, runways and hard standings. The excellent fuel resistance of Colpor 200 makes it particularly suitable for sealing areas where fuel and oil spillage might occur, such as:
  – Aircraft fuelling areas
  – Oil terminals
  – Garage forecourts
  – Parking and cargo areas
  – Docks and harbours
  – Warehouses

  ADVANTAGES

  – Cold applied – no heating required
  – Fuel, oil and hydraulic fluid resistant
  – Self-levelling
  – Tough, rubbery seal
  – High performance – less maintenance

  MIXING

  Drain the curing agent into the large base tin. Always use a handheld, slow speed drill (400 to 500 rpm) fitted with a Fosroc paddle blade stirrer. Mix for approximately one minute, stop the mixer and scrape around the top of the tin to remove any remaining curing agent. Continue mixing for a further 3- 4 minutes until the material is mixed thoroughly.

  APPLICATION

  When mixed, the sealant may be loaded into a 600ml barrel gun after removing the nozzle and cap then pulling back the plunger rod. Apply the material directly into the joint, making sure the top of the sealant is recessed below the concrete edge & not level.

  For all other Fosroc products on our website, please click here. For any further information on Fosroc products, please visit their website here.

  PLEASE NOTE THIS PRODUCT CAN ONLY BE COLLECTED FROM STORE & WILL NOT BE SENT VIA COURIER.

  Add to basket

  View Details
• 

  FOSROC Galvafroid Thinners Cleaner 400ML Tin

  £32.55 £23.99

  Product Description

  FOSROC Galvafroid Thinners Cleaner is a zinc-rich coating formulated & designed as an easily applied, cold galvanising protector against corrosion on all types of ferrous metals. Galvafroid has a mid-grey, matt finish when cured

  Best Uses

  FOSROC Galvafroid Thinners Cleaner is formulated to provide galvanic protection on steel & iron. Galvafroid can be used as a self-finishing or as a durable, rust-inhibiting primer beneath selected topcoats. It is advised to be used for the protection of agricultural and construction plant and machinery, structural steelwork, railings, gates, iron pipework and guttering, and the rust prevention of in-situ welding work.

  Benefits

  – Protects ferrous metals against rust
  – Suitable to be used as a primer or self-finish
  – Easily applied, using either a brush or a roller

  Application

  All ferrous surfaces need to be clean and free from oil, grease, existing coatings & rust. This is best by either grit blasting or thorough wire brushing. Where required, Galvafroid Thinners can be used to increase durability or to enhance the appearance of steel or iron finishes. 

  For all other Fosroc products that are available on our site, please click here.

  For any further info you may require on Fosroc products, feel free to visit their website here.

  Add to basket

  View Details
• 

  FOSROC MS2 Primer 750ml

  £87.99 £75.99

  FOSROC MS2 is a two-part priming system used in conjunction with Fosroc Nitoseal sealant range. It is required for use in joints alongside Nitoseal that are set to be intermittently or permanently immersed in water, or where the substrate is likely to be saturated (for example, externally).

  FOSROC MS2 Nitoseal primer is formulated for priming prior to application of the sealant

  Application

  Empty the entire contents of the hardener tin into the base tin, replace the base tin cap. Mix by shaking thoroughly for 2 minutes. Prime the joint face using a dry, clean brush. Avoid over-application of the primer & avoid causing puddles in the bottom of the joint. The sealant should be applied between 30 minutes & 4 hours after the primer has been applied. If the area is not sealed within this time frame, the primer residue will need to be removed by either grit blasting or grinding, before the primer can be reapplied. The mixed Primer MS2 solution must be applied within one working day. Do not use part packs.

  For all other FOSROC products available on our website, please click here.

  For any further information you require or need on FOSROC, please visit their website here.

  Add to basket

  View Details
• 

  FOSROC Nitoseal MS600

  £16.95 £13.50

  FOSROC Nitoseal MS600 is suitable for sealing movement joints in buildings and civil engineering structures including joints that will be subject to intermittent immersion.

  Typical applications include:

  – Reservoirs
  – Sewage tanks
  – Sea walls
  – Basements
  – Subways
  – Parapets
  – Bridges
  – Superstructures

  Advantages

  – Approved for use in contact with potable water
  – Meets key international standards
  – Resistant to aerobic and anaerobic bacteriological attack
  – Excellent resistance to acids and alkalis
  – Cures to a tough, elastic seal
  – Accommodates continuous cyclic movement
  – High resistance to ageing
  – Single component yet fast rate of cure
  – Can be applied to damp substrates
  – Isocyanate free technology

  Description

  Nitoseal MS600 is a one part medium modulus sealant based on hybrid silyl modified polyether technology. It has a fast rate of cure and forms a tough, highly durable and water resistant elastomer. Conforms to the Water supply Regulations 2000 & 2001 Regulations 31(4b) for products having a small surface area in contact with water for public supply.

  Instructions to use

  Preparation

  Joint surfaces must be clean & dry. Remove all dirt & loose materials and any foreign matter. Remove all rust, scale and protective lacquers from metal surfaces.
  Removal can be achieved by rigorous wire brushing or grit blasting.

  Joints in concrete should preferably be sawn. After sawing, all saw slurry must be flushed away and the joint allowed to dry. When resealing, the existing sealant should be removed from the joint and cleaned back to sound clean concrete. Any expansion joint filler must be checked to ensure it is tightly packed and no gaps or voids exist.

  The use of a bond breaker is not required in expansion joints containing cellular polyethylene joint filler such as Hydrocell XL or Expandafoam. For construction or contraction joints a bond breaker tape or back-up strip should be used. Where a particularly neat finish is required, mask the face edges of the joint before sealing and remove immediately after tooling.

  Priming

  Fosroc Primer MS2 is required for joints that are to be intermittently or permanently immersed or where the substrate is likely to saturated. When using a primer, empty the entire contents of the
  hardener tin into the base tin and replace the base tin lid. Mix thoroughly by shaking for at least 2 minutes. Prime the joint face using a clean, dry brush. Nitoseal MS600 should be applied between 30 minutes and 2 hours after priming. If a joint is left unsealed for more than 2 hours, the primer should be removed by grit blasting or grinding and the joint re-primed.

  Do not split packs of Fosroc Primer MS2

  Add to basket

  View Details
• 

  FOSROC Nitoseal PU800 – 2 Litre Tin

  £80.00

  FOSROC Nitoseal PU800 is primarily for sealing internal joints subject to abrasion & heavy loading, or where chemical resistance is needed. Can be used in warehouses and distribution centres. It is, particularly useful forklift trucks are in use. FOSROC Nitoseal PU800 can also be used where joints would be subject to shoes with high heels, shopping malls, podiums etc. It is abke to be used in prisons as an anti-pick sealant for sealing internal partitions, cell doors and windows, fittings and furniture.

  Advantages

  – Cures to a tough seal
  – Abrasion-resistant
  – High modulus
  – Resistant to chemical, fuel and oil spillage
  – Easily installed to give a flush finish
  – Hard & flexible sealant; resists picking and vandalism

  Description

  FOSROC Nitoseal PU800 is a two-component gun grade elastomeric sealant for joints with limited movements. After mixing, the resultant mix will cure to provide an exceptionally robust seal, while retaining a degree of some flexibility. PU800 can abrasion can withstand spillage of oils, fuels, vegetable oils & mineral acids.

  Preparation

  Joint surfaces shall be dry, clean and free from contamination. Any voids or gaps at the base of the sealing slot should be filled, and a suitable bond breaker should be pushed into construction and contraction joint slots. Where a particularly neat finish is required mask edges of joint before priming (if needed) and application.

  Priming

  Where surface shall be subject to submersion or permanently damp, joints should be primed using Fosroc Primer MS2. Decant the entire contents of primer curing agent into the primer base tin and replace the lid. Mix thoroughly by shaking tin for about 2 minutes. Apply the primer using a clean, dry paintbrush. Nitoseal PU800 should be applied between 30 minutes and 4 hours after priming.

  ---

  For all other Fosroc products on our website, please click here. Please note you require a barrel gun to apply this foil sealant, please see our options by clicking here or our recommended sealant gun here.

  For any further you may need on Fosroc products, please visit their website here.

  Add to basket

  View Details
• 

  FOSROC Primer 7 – Surface primer for polysulphide sealant 500ml

  £49.95 £44.34

  Fosroc primer 7 comes as a ready to use, brush-on liquid, that prepares porous surfaces such as stone, brickwork, concrete, timber and un-glazed edges of ceramic tiles before the application of Thioflex 600.

  Uses

  Primer 7 is used to prime concrete joint edges before applying Thioflex 600 polysulphide joint sealants. If the joints are likely to be subject to long term moisture, then Primer 13 should be considered.

  Advantages

  – Fast-drying – enables sealant work to progress
  – Single component – no mixing required

  Description

  Primer 7 is a low viscosity one-component solvent-based priming system for concrete joints before the installation of Thioflex 600 joint sealants.

  Technical Support

  – Easy to use, brush applied primer
  – Essential for use with Thioflex 600
  – Widely used for the priming of movement joints in building and civil engineering structures that are being sealed with Thioflex 600

  For all other FOSROC products on our website, please click here.

  For any further information on Fosroc products, please visit their website here.

  Add to basket

  View Details
• 

  FOSROC Thioflex 600 Gun Grade – 2.5Litre

  £39.99 £29.95

  FOSROC Thioflex 600 is available in gun and pouring grades. The gun grade is ideal for general application.

  ADVANTAGES

  – Meets key international standards
  – Forms a robust, elastic, rubber-like seal
  – Accommodates continuous and pronounced cyclic movement

   

  APPLICATION INSTRUCTIONS

  Joint preparation

  The joint surfaces must be dry, clean and free of frost. Remove any dust by rigorous wire brushing, grinding or grit blasting. Also, all rust, scale and protective lacquers must be removed from metal surfaces. Also, any expansion joint filler must be checked to ensure it is tightly packed, and no gaps or voids exist at the base of the sealing slot before positioning a bond breaker.

  Note: The use of a bond breaker is not required in expansion joints containing Hydrocell XL or Expandafoam cellular polyethylene expansion joint fillers.

  Priming

  Priming should be achieved by applying one thin coat, using a clean, dry brush, ensuring complete coverage, then applying sealant once the primer is tack-free. If left for 3 hours, the surfaces must be reprimed before applying the sealant. Iron and steel must be protected with an anti-corrosion primer before sealing.

  Mixing

  Mix thoroughly using a slow speed drill fitted with a mixing paddle for at least 5 minutes. Thoroughly mixing all contents, including material right at the bottom of the tin. Immediately after mixing, load the sealant into a barrel Gun using the Follower Plate, and apply to the joint.

  For all other Fosroc products on our website, please click here.

  For any further information you may nee on Fosroc products, please visit their website here.

   

  Add to basket

  View Details
• 

  FOSROC Thioflex 600 Pour Grade – 5 Litre

  £89.99 £75.20

  FOSROC Thioflex 600 Gun Grade is a multi-component, gun grade, polysulfide sealant. FOSROC Thioflex 600 Gun Grade is ideal for general application. FOSROC Thioflex 600 Gun Grade comes in a tin containing the base and curing agent in the correct proportions. Thioflex 600 is particularly recommended for use in high-rise buildings as well as also being suitable for sealing joints in brickwork, retaining walls, basements and subways.

  This product comes in a 5litre tin.

  Info: Meets key international standards. Standards compliance British Standard BS 4254: 1983. U.S. Federal Specification TT-S-00227E November 1969 (amended 1970). DTP specification for Highway Works December 1991 series 1000 clause 1017. ASTM C920-87: Type M, Grade NS, Class 25.

  Forms a tough, elastic, rubber-like seal. Accommodates continuous and pronounced cyclic movement. Excellent adhesion to most common substrates, including primed concrete, glass, aluminium and stainless steel! Benefits from high resistance to ageing reduce physical damage due to climatic extremes.

  Add to basket

  View Details