Bond It Anchor Bond Adhesive 310ml
£4.62 inc. VAT
£3.85 ex. VAT
- Product ID: BDAB310
- Suitable For: setting bolts, studs, wall ties, starter bars or large screws, etc.
- Area of use: INT & EXT
- Application Method: silicone gun
- Volume: 310ml
- Container Type: cartridge
- Type: adhesive
- Colour: grey
- Brand: Bond It
- Manufactuer: Bond It
- Box Size: 1
Bond It Anchor Bond is a 2-part system applied in one single action to produce a cost-effective, tough chemical resistant fixing. Ideal day to day applications include: railings, steel structures, satellite dishes, fire surrounds, gates, sanitary fixings/towel holders, pipes and lamps. Use of Anchor Bond makes the fixing an integral part of the substrate as the load is spread throughout the entire fixing area as opposed to when plastic plugs or mechanical fixings are used especially in friable or cracked substrates.
For more in our range of glues and adhesives, please click here. Or to shop our range of Bond It products, click here.
To visit Bond It’s website, please click here.
Anchor Bond is suitable for setting bolts, studs, wall ties, starter bars or large screws, etc into a wide range of substrates. Compatible with brickwork, concrete, masonry, stone and PFA blocks. Hollow base materials can also be securely fastened using Anchor Bond in conjunction with a sleeve or sieve.
Chemically resistant, waterproof and vibration proof.
PREPERATION
Drill a hole to the correct diameter and depth (see chart over leaf), ideally using a rotary percussion machine. For optimum results the wall sides should be thoroughly roughened. Clean hole
and remove all dust and debris using a hand air pump or a stiff rotary brush, if required. All bars should be clean and free from oil or grease and all flaking rust should be removed. Threaded rods or studs should be chisel ended to prevent them being unscrewed from the cured resin.
APPLICATION
Screw the mixing nozzle on to the cartridge (hand tighten). Place the cartridge into the dispensing gun. Squeeze the hand trigger a few times until material passes through the mixing nozzle. Allow the material to flow until an even colour is obtained (normally 5-6 inches). Insert the nozzle into the base of the hole and extrude material, half filling the hole with resin. Withdraw the nozzle then insert the fixing into the filled hole, slowly rotating to fully coat the surface. After application release the pressure from the dispensing gun. Remove the used mixing nozzle and wipe away excess material from the end of the cartridge. Once the resin has cured the fixture can be attached to the fixing and fully tightened. Do not over pressurise cartridge otherwise leakage may occur from rear pistons.
2 reviews for Bond It Anchor Bond Adhesive 310ml
You must be logged in to post a review.
| Elementlength | |||||||
| up to 1,5 m |
up to 2,5 m |
up to 3,5 m |
up to 4,5 m |
up to 2,5 m |
up to 3,5 m |
up to 4,5 m |
|
| Type of window frame material |
Minimum witdth of joints for a butled mounting b in mm |
Minimum witdth of joints for a inner mounting b in mm |
|||||
| Hard PVC (white) | 10 | 15 | 20 | 25 | 10 | 10 | 15 |
| Hard PVC and PMMA (dark) (colour extruded) |
15 | 20 | 25 | 30 | 10 | 15 | 20 |
| Hard PUR integral foam | 10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Wood-aluminium-window | 10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Aluminium-plastic sandwich frame (bright) |
10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Aluminium-plastic sandwich frame (dark) |
10 | 15 | 20 | 25 | 10 | 10 | 15 |
| Wooden window frame | 10 | 10 | 10 | 10 | 10 | 10 | 10 |
Related Products
From:
From:
-
£37.01 inc. VAT
£30.84 ex. VATBond-It De-Bond Mate is A non-drip gel formula for the complete removal of cured silicone sealant, particularly when silicone has been accidentally smeared over glass, ceramics or countertops. Removes all types of silicone sealant, leaving surfaces ready for re-sealing. For all other Bond-it products on our website, please click here. For any further information, you may need on Bond-it, please visit their website here. -
£70.80 inc. VAT
£59.00 ex. VATBond-it Flash Mate Lead Silicone is a low modulus neutral cure fast-skinning, roof sealant It is a high-performance neutral cure silicone sealant, specifically designed for use with roofing products both modern and traditional. For all other Bond-it products on our website, please click here. For an alternative silicone for lead, click here. For any further information you may need on Bond-it, please visit their website here. -
£8.14£1.19 inc. VAT£6.78£0.99 ex. VAT
£8.14£1.19 inc. VAT£6.78£0.99 ex. VATARBO Arbosil 1070 represents a single-component, Low Modulus Silicone Sealant with Fire-Resistant properties. It undergoes curing upon exposure to moisture vapor, ultimately transforming into a highly flexible silicone rubber material. For more information on Arbo, please visit their website here. For more in our range of sealants, please click here. For application guns to use with this product, please click here. -
From:£3.83£1.19 inc. VAT£3.19£0.99 ex. VATArbosil HM is a One-part High Modulus Acetoxy Cure Silicone Sealant, which cures rapidly on exposure to moisture vapour to form a resilient elastic silicone rubber. This product contains a fungicide to make it resistant to fungus and mildew. Arbosil HM bonds well to acrylic, ceramic, metal, glass and laminate surfaces and will not discolour during its service life whilst maintaining good elasticity. For more information on Arbo, please visit their website here. For more in our range of sealants, please click here. For application guns to use with this p
Gareth (verified owner) –
Excellent product and price was very good
Pauline B. (verified owner) –
Product arrived but was one item short so contacted supplier who apologised and I received the item in a few days so no complaints