Total: £0

toly (Price shown excludes VAT)

01708 525 866

Total: £0

toly (Price shown excludes VAT)

General Sealants

  • arbo-1096

    Arbo Arbosil 1096

    £4.65

    Arbo Arbosil 1096 is a one-part Low Modulus Neutral Cure Silicone, which cures upon exposure to moisture vapour to form an elastic, rubber-like silicone.

    Recommended for use in a wide range of construction applications, including glass to glass joints, curtain wall assemblies, perimeter seals to curtain walls, perimeter sealing to polyester powder coated and PVCu frames. Approved for use with laminated glass by several manufacturers. Suitable for use as a weather seal on structural glazing applications.

    This product is not recommended for overpainting and use against natural stone.

    APPLICATION

    Preparation

    The surfaces must be dry, clean and free from any contamination. The surfaces should be degreased using an appropriate cleaner. Primers may be required on some surfaces. It is advised that Adshead Ratcliffe Technical Services Department should be consulted and information obtained about the choice of primer for specific purposes.

    Joint Backing

    Where applicable, an appropriate joint filler, e.g. closed-cell polyethylene foam, should be used to provide the correct depth for the joint. All preparation, priming, and sealant application should be carried out following BS 8000 Part 16. This is the British Standard for the sealing of joints in buildings using sealants.

    Application

    Arbosil 1096 is supplied in a 380ml cartridges and can be applied into the joint using a sealant application gun.

    JOINT SIZE SUITABILITY

    Joint Width

    Minimum 6mm
    Maximum 25mm (single application);
    50mm (multiple applications)

    Joint Depth

    Minimum 10mm on porous substrates
    Minimum 6mm on non-porous substrates
    Maximum 15mm

    HEALTH & SAFETY

    Contains Oximosilanes. Please consult the MSDS for full information.

    STORAGE LIFE

    Twelve months in original unopened packaging stored in a cool, dry place out of direct sunlight.

    We also stock a wide range of other Arbo Products on our website.

    For any further information, you may need, please visit the Arbo Website.

  • arbo-1096-box-25

    Arbo Arbosil 1096 – Box of 25

    £105.50

    Arbo Arbosil 1096 is a one-part Low Modulus Neutral Cure Silicone, which cures upon exposure to moisture vapour to form an elastic, rubber-like silicone.

    Recommended for use in a wide range of construction applications, including glass to glass joints, curtain wall assemblies, perimeter seals to curtain walls, perimeter sealing to polyester powder coated and PVCu frames. Approved for use with laminated glass by several manufacturers. Suitable for use as a weather seal on structural glazing applications.

    This product is not recommended for overpainting and use against natural stone.

    APPLICATION

    Preparation

    The surfaces must be dry, clean and free from any contamination. The surfaces should be degreased using an appropriate cleaner. Primers may be required on some surfaces. It is advised that Adshead Ratcliffe Technical Services Department should be consulted and information obtained about the choice of primer for specific purposes.

    Joint Backing

    Where applicable, an appropriate joint filler, e.g. closed-cell polyethylene foam, should be used to provide the correct depth for the joint. All preparation, priming, and sealant application should be carried out following BS 8000 Part 16. This is the British Standard for the sealing of joints in buildings using sealants.

    Application

    Arbosil 1096 is supplied in a 380ml cartridges and can be applied into the joint using a sealant application gun.

    JOINT SIZE SUITABILITY

    Joint Width

    Minimum 6mm
    Maximum 25mm (single application);
    50mm (multiple applications)

    Joint Depth

    Minimum 10mm on porous substrates
    Minimum 6mm on non-porous substrates
    Maximum 15mm

    HEALTH & SAFETY

    Contains Oximosilanes. Please consult the MSDS for full information.

    STORAGE LIFE

    Twelve months in original unopened packaging stored in a cool, dry place out of direct sunlight.

    We also stock a wide range of other Arbo Products on our website.

    For any further information, you may need, please visit the Arbo Website.

  • arbo-hm

    Arbo Arbosil HM

    £2.25

    Arbo Arbosil HM is a One-part High Modulus Acetoxy Cure Silicone Sealant, which cures rapidly on exposure to moisture vapour to form a resilient elastic silicone rubber. This product contains
    a fungicide to make it resistant to fungus and mildew. Arbosil HM bonds well to acrylic, ceramic, metal, glass and laminate surfaces, and will not discolour during its service life, whilst maintaining good elasticity.

    MAIN APPLICATIONS

    This product is recommended for the sealing around all types of sanitary fittings including baths, showers, urinals, sinks and washbasins in both domestic and commercial locations.

    – It is suitable for use in areas of high humidity.
    – Can be used to seal around laminates and worktops.
    – Suitable for both interior and exterior use.
    – Use for sealing of aluminium sheets and components.
    – Use as an adhesive to bond PVC trims

    APPLICATION INSTRUCTIONS

    Joint Preparation

    The joint surfaces must be clean, dry and free from all contamination and any loose materials. The surfaces should be decreased using the appropriate Arbo Cleaner. Primers
    may be required on some substrates. It is recommended that Adshead Ratcliffe Technical Services Department should be consulted and advice obtained with regard to
    the choice of primer for specific purposes.

    Joint Backing

    Where applicable, appropriate joint filler e.g. closed-cell polyethene foam should be used, to provide the correct joint depth.

    Application

    Arbosil HM is supplied in cartridges and can be applied into the joint using an Arbo Caulking Gun. All joint preparation, priming, and sealant application should be carried out
    in accordance with BS 8000 Part 16, the British Standard for the sealing of joints in buildings using sealants.

    STORAGE LIFE

    12 months in original unopened package stored in a cool, dry place out of direct sunlight. Protect from frost.

    HEALTH & SAFETY

    No particular health hazards are associated with this product but please consult Material Safety Data Sheet for full information.

    You can also find a wide range of other Arbo products on our website.

    For any further information, you may need, please visit the Arbo website.

  • arbo-hm-box-of-25

    Arbo Arbosil HM – Box of 25

    £52.75

    Arbo Arbosil HM Box of 25

    Arbo Arbosil HM is a one-part High Modulus Acetoxy Cure Silicone Sealant, which cures rapidly on exposure to moisture vapour to form a resilient elastic silicone rubber, suitable for use in a range of environments.

    Arbosil HM is also resistant to fungus and mildew due to the fungicide present in this sealant. Arbosil HM bonds well to acrylic, ceramic, metal, glass and laminate surfaces, and will not discolour during its service life, whilst maintaining good elasticity.

    MAIN APPLICATIONS

    This product is recommended for the sealing around all types of sanitary fittings including baths, showers, urinals, sinks and washbasins in both domestic and commercial locations.

    – It is suitable for use in areas of high humidity.
    – Can be used to seal around laminates and worktops.
    – Suitable for both interior and exterior use.
    – Use for sealing of aluminium sheets and components.
    – Use as an adhesive to bond PVC trims

    APPLICATION INSTRUCTIONS

    Joint Preparation

    The joint surfaces must be clean, dry and free from all contamination and any loose materials. The surfaces should be decreased using the appropriate Arbo Cleaner. Primers may be required on some substrates. It is recommended that Adshead Ratcliffe Technical Services Department should be consulted, and advice obtained with regard to the choice of primer for specific purposes.

    Joint Backing

    Where applicable, appropriate joint filler e.g. closed-cell polyethene foam should be used, to provide the correct joint depth.

    Application

    Arbosil HM is supplied in cartridges and can be applied into the joint using an Arbo Caulking Gun. All joint preparation, priming, and sealant application should be carried out
    in accordance with BS 8000 Part 16, the British Standard for the sealing of joints in buildings using sealants.

    STORAGE LIFE

    12 months in original unopened package stored in a cool, dry place out of direct sunlight. Protect from frost.

    HEALTH & SAFETY

    No particular health hazards are associated with this product but please consult Material Safety Data Sheet for full information.

    You can also find a wide range of other Arbo products on our website.

    For any further information, you may need, please visit the Arbo website.

  • bathroom-and-kitchen-box-of-25

    Bond-It Bath-Mate Bath & Kitchen Sealant – Box of 25

    £44.00

    Bond-It Bath-Mate Bath & Kitchen Sealant

    Bond-It Bath-Mate is a high quality, permanently flexible, water-based sealant with excellent adhesion to plastic, ceramic tiles, wood and porcelain. It can be overpainted and is easy to use. Often this sealant is also used as a method to repair grout and improve the appearance of a tired and worn bathroom or kitchen.

    Uses

    Bond-It Bath-Mate BATH & KITCHEN SEALANT can be used to seal around ceramic baths, sinks and worktops, forming a watertight bond to the surfaces. Contains a powerful anti-fungal compound to prevent mould growth. Easy to apply and any mistakes can be easily rectified with water.

    Preparation

    All surfaces must be clean, dry, sound and free from dust, oil or any other contaminants that may hinder adhesion.

    Priming

    Bond It BATH & KITCHEN SEALANT does not require a primer on most common construction surfaces. To determine whether a primer is necessary, a sample should be tested. Contact Bond It Technical Service Department for recommendations.

    Application

    Apply using a standard sealant gun. Cut tip from the cartridge, be careful not to damage the screw thread. Cut the nozzle at an angle of 45° to an opening slightly larger than the gap to be sealed. Apply using a standard sealant gun. Smooth down within 15 minutes using a slightly wetted spatula. Remove excess product with a damp cloth. Do not saturate the surface with water, as this will delay curing the process.

    We have a number of tools on our website that would assist with the application of this product. We would recommend using a PC Cox Skeleton Gun to apply & a Bond-it Tooling Kit to aid in providing a professional finish.

    Limitations

    Not suitable when:
    – Applied externally during rainy weather.
    – Applied at temperatures below +5°C.
    – Not suitable for plastic baths – use a sealant with greater flexibility.
    – Do not use in joints immersed continuously in water.
    – Can not be used in contact with bituminous products.
    – Used in areas of high abrasion, e.g. floor joints.
    – This product is not a silicone sealant!

    For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it, please visit their website here.

  • lead-mate-box-of-25

    Bond-it Flash Mate Lead Silicone – Box of 25

    £59.75

    Bond-It Flash Mate Lead Silcone – Box of 25

    Bond-it Flash Mate Lead Silicone is a low modulus neutral cure fast-skinning, roof sealant. It is a high-performance neutral cure silicone sealant, specifically designed for use with roofing products both modern and traditional.

    A cost-effective option of specialist trades people who require a reliable sealant which they can use across multiple projects and environments.

    Uses

    Bond-it Flash Mate can be used to bond glass and glazing plastics as well as small sections of roofing materials under repair. Ideally suited for sealing roof lights, conservatories, soffit boards, glasshouses, industrial roofing systems, lead flashing and to prevent tile lifting and wind noise.

    It is ideal for use on:
    – Glass
    – Slate
    – All metals including lead and galvanised steel
    – Concrete and brick
    – GRP
    – Sealed timber
    – Plastics (including poly-carbonate)
    – Acrylics
    – PVCu
    – All painted surfaces

    Application

    Apply using a standard sealant gun. Cut the nozzle at a 45° angle using a sharp blade, to an opening slightly larger than the joint you wish to seal. Allow a minute or two before tooling for the best results. For bonding, press the two surfaces together before skinning commences. On very hot roofs skinning time will be much shorter. Once the silicone has been applied and tooled, the rain will not have any adverse effects on the sealant.

    For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it, please visit their website here.

  • gp200-box-of-25

    Bond-It GP200 Contractors Grade Silicone – Box of 25

    £48.75

    Bond-It GP200 is a multi-purpose, low modulus silicone rubber sealant with fungicide, suitable for most sealing jobs around the home.

    Uses

    Bond It GP 200 is ideal for sealing in areas of high humidity. Therefore it has excellent adhesion to glass, glazed surfaces, ceramic tiles, many plastics and most paints.

    It is suitable for the following applications – kitchen worktops, bathrooms, showers, utility rooms and general DIY applications.
    – Car
    – Boat
    – Caravan
    – House

    Preparation

    Ensure all surfaces are clean and free from grease. All types of cement, concretes and bare metal surfaces should be primed before the application of the silicone. Timber should be primed and painted.

    Application

    Apply using a sealant gun with the nozzle cut at a 45° angle, and to an opening slightly larger than the joint to be sealed. Smooth using a stick or plastic spatula wetted with a soap & water solution. Can not be applied to wet surfaces, although wetting immediately afterwards will not have any adverse effects. After that, tools can be cleaned in white spirit prior to curing taking place.

    Limitations

    Bond-It GP200  is not suitable for fixing of mirrors or sealing natural marble.

    For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it, please visit their website here.

  • lami-mate-box-of-12

    Bond-It Lami-Mate Timber Sealant – Box of 12

    £29.04

    Bond-It Lami-Mate Timber Sealant is a polymer enhanced, flexible sealant and gap-filler designed for sealing all tongue and groove laminate flooring. When cured it can be varnished or wood stained if required.

    Uses

    Bond-It Lami-Mate stays permanently flexible and can be used for sealing all types of laminate and hardwood flooring. It can also be used for sealing around timber window and door frames as well as all types of fitted furniture. For example, bedroom and kitchen fittings, laminate worktops etc. LAMI-MATE is also suitable for sealing glass panels into kitchen unit doors. In addition, it is suitable for internal and external use.

    Application

    Apply using a standard sealant gun. Cut the nozzle at a 45° angle with a sharpe blade, making sure not to damage the thread.  The nozzle should be cut to an opening slightly larger than the joint tha is to be sealed. Smooth down using a slightly wetted spatula, dampened with a soap & water solution.

    We have a number of tools on our website that would assist with the application of this product. We would recommend using a PC Cox Skeleton Gun to apply & a Bond-it Tooling Kit to aid in providing a professional finish.

    Limitations

    Do not use in conjunction with bitumen or asphalt. For perimeter use only, do not use in areas subject to mechanical abrasion. Furthermore, do not attempt to sand down.
    Caution: The colour on application will be different from the colour achieved when fully cured.

    Container Size

    EU3 plastic cartridge.

    Colours

    LAMI-MATE comes in 4 colours: teak, pine, dark oak and light oak.

    For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it, please visit their website here.

  • multi-mate-box-of-25

    Bond-it Multi Mate GP Silicone – Box of 25

    £59.25

    Bond-it Multi Mate GP Silicone is a high modulus, acetoxy cure silicone sealant with fungicide, suitable for most sealing jobs around the home.

    Uses

    Bond-it Multi Mate has excellent adhesion to glass, glazed surfaces, ceramic tiles, aluminium, many plastics and most
    paints. It is ideal for the following applications – kitchen worktops, bathrooms, showers, utility rooms and general DIY applications.
    – Car
    – Boat
    – Caravan
    – House

    Preparation

    Ensure all substrates are dry and free from grease or any contaminants that may hinder adhesion. For best results on movement joints, use a backing material, or a suitable backing tape or rod. All types of concretes and bare metal surfaces should be primed prior to the application of the silicone.

    Application

    Apply using a standard sealant gun with the nozzle cut at a 45° angle, and to an opening that is larger than the joint that is to be sealed. Tool using a piece of smooth wood wetted with soapy water.

    Bond-It Lami-Mate Timber Sealant is a polymer enhanced, flexible sealant and gap-filler designed for sealing all tongue and groove laminate flooring. When cured it can be varnished or wood stained if required.

    Uses

    Bond-It Lami-Mate stays permanently flexible and can be used for sealing all types of laminate and hardwood flooring. It can also be used for sealing around timber window and door frames as well as all types of fitted furniture. For example, bedroom and kitchen fittings, laminate worktops etc. LAMI-MATE is also suitable for sealing glass panels into kitchen unit doors. In addition, it is suitable for internal and external use.

    Application

    Apply using a standard sealant gun. Cut the nozzle at a 45° angle with a sharpe blade, making sure not to damage the thread.  The nozzle should be cut to an opening slightly larger than the joint tha is to be sealed. Smooth down using a slightly wetted spatula, dampened with a soap & water solution.

    We have a number of tools on our website that would assist with the application of this product. We would recommend using a PC Cox Skeleton Gun to apply & a Bond-it Tooling Kit to aid in providing a professional finish.

    Limitations

    Do not use in conjunction with bitumen or asphalt. For perimeter use only, do not use in areas subject to mechanical abrasion. Furthermore, do not attempt to sand down.
    Caution: The colour on application will be different from the colour achieved when fully cured.

    Where bare ferrous metals, brass copper, lead or zinc cannot be primed, use Bond It ULTI-MATE Silicone Sealant. Furthermore, do not use on surfaces where water can penetrate through porous materials to affect the bond. Not suitable for fixing mirrors or sealing natural marble.

    Container Size

    EU3 plastic cartridge.

    Colours

    LAMI-MATE comes in 4 colours: teak, pine, dark oak and light oak.

    For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it, please visit their website here.

  • glazing-sealant-box-of-25

    Bond-It Pro-Mate LMA Glazing Silicone – Box of 25

    £57.75

    Bond-It Pro-Mate LMA Glazing Silicone is a low modulus, silicone sealant. Ideal for exterior and interior applications where the joint movement does not exceed 20%

    Uses

    Bond-It Pro-Mate is suitable for sealing around doors and windows and for general building maintenance.
    It is ideal for use on:
    – Glass to glass
    – Aluminium to glass
    – Glass
    – Ceramics
    – Most common building materials.

    Preparation

    Before application, ensure all substrates are clean and free from grease or any contaminants that could prevent the product from achieving required adhesion.

    Application

    Apply using a standard-sized sealant gun. Cut the tip from the cartridge with a sharp Stanley blade, making sure not to damage the thread. Cut the nozzle at an angle and fix to the cartridge. Using the gun, apply the sealant to the joint, making sure to achieve the required depth for the joint size. This ensures the sealant will perform at it’s best once cured. Tool off using a spatula or a piece of smooth wood dampened with a soapy water solution.

    Limitations

    Not suitable for use on un-primed metals, types of cement or concrete. In areas subject to fungal or mould growth Bond It, MULTI-MATE silicone should be applied. Joints in which water generates pressure through the substrates on the sealant bond require remedial work before application.

    For all other Bond-it products on our website, please click here.

    For any further information you require on Bond-it, please visit their website here.

  • all-weather-box-of-12

    Bond-It Rain Mate All Weather Sealant – Box of 12

    £34.32

    Bond-It Rain Mate All Weather Sealant is a superior and highly flexible, water repellent, general purpose sealant that has excellent adhesion to all surfaces, even when damp.

    Uses

    It suitable for use on brick, concrete, stone, all metals, painted or bare wood, glass, vinyl and most plastics. Also, it is compatible with bitumen and asphalt for roof repairs in damp conditions. Finally, it is ideal for sealing doors, windows, roofs, cladding and vehicle bodies.

    Application

    Primers are not usually required. For application in damper conditions, disburse any standing water and residual dirt from the substrate.  Dry the surface as well as possible with either a cloth or paper towel prior to applying sealant. All RAIN-MATE colours will adhere to bitumen and asphalt but we only recommend black for this purpose as unsightly discolouration can occur with white and clear.

    Limitations

    Not for use on polystyrene, polycarbonate, plastic roof lights or other surfaces sensitive to solvents. Do not apply at over 60o C or on surfaces which exceed 80o C in use.

    Health & Safety

    Please refer to the safety data sheet for full handling, use and storage instructions. Keep out of reach of children.

    For all other Bond-it products on our website, please click here.

    For any futher information you may need on Bond-it, please visit their website here.

  • roof-and-gutter-box-of-25

    Bond-It Roof & Gutter Mate Sealant – Box of 25

    £33.75

    Bond-It Roof & Gutter Mate is suitable for repairing and maintaining general roofing and roof drainage systems. It forms a flexible seal that remains flexible for up to 15 years with a movement allowance of 5%.

    It is ideal for use on a range of construction substrates, such as:

    – Metal
    – Construction grade plastics
    – Paint
    – Stone
    – Brick
    – Bitumen

    PREPARATION

    Ensure all surfaces are clean and free from grease or any contaminants that may hinder adhesion. Loose materials and signs of corrosion must be removed before application as they will also hinder adhesion.

    APPLICATION

    Apply using a standard sealant gun. Cut tip from the cartridge, be careful not to damage the screw thread. Cut the nozzle at an angle of 45° and fix to the cartridge. Using a caulking gun force the sealant
    into the joint. When a deep joint is being sealed, a backing tape should be applied.

    COLOURS

    Bond-It Roof & Gutter Mate comes in black only.

    SHELF LIFE

    Use within 2 years from the date of manufacture.
    Store in unopened cartridges in a cool & dry environment.

    For all other Bond-it products on our website, please click here.

    For any further information you may need on Bond-it products, please visit their website here.

Builders Sealant

As a trade specialist, we understand your requirements for builder’s sealant mean that you need a reliable provider with flexible delivery times.

At Sealant Supplies we are a one-stop shop for all of your sealant requirements, with an extensive range of brands, sealant types and accessories and tools available via our website. We regularly update our stocklist to ensure we provide the best options on the market to our customers.

Builder’s sealants include bathroom, kitchen, general, external and many more different types of sealants. At SSL we understand the pressures as a builder to deliver a high-quality project in short timeframes. This is exactly why we aim to ship all of our orders the next working day, ensuring our customers receive their sealants as quickly as possible.

We also stock a variety of sealants to ensure we can offer our customers a full range of products, making us the only place to shop for builder’s sealants.

We also regularly run promotions and discounts on our sealants for our trade clients. Opening a trade account with SSL is easy to do. Our trade customers also benefit from bulk discounts and offers on repeat orders.

Alongside our trade accounts we also offer credit accounts for those ordering builder’s sealants, do not hesitate to get in touch with our team for more information.